|
December 23, 2008 00:12 AM  BY STACEY BARRUS
|
|
|
For homeowners or
renovators, it’s worth taking a look at several kinds
of radiant heaters for residences or
businesses. Today we’ll discuss the electric
cable heating system kind of radiant heaters.
Electric cable heating systems, often called
line- or high-voltage systems, are gaining popularity
and are ideal for heating smaller areas like
bathrooms, kitchens, and sun rooms. These systems are
comprised of a thermostat and a heating cable. On some
radiant
heater systems, the cable will be shipped to
you as a large spool of cable. These systems are
oftentimes less expensive, and give you the ability to
space the cable how you want and customize a layout that
will heat every square inch of your floor. Other
systems have the cable attached to a plastic mesh or
tape to create a mat to maintain its proper spacing.
Every available radiant heater cable system is
equally effective, so when determining which system to
purchase, you should look at the warranty of the
product, along with the ease of installation. Some cables
must be embedded in a separate layer of concrete or
mortar, whereas other systems can simply be installed
in the thinset.
Most cable systems can only be installed under
tile; on others, if the cable is embedded in mortar or
concrete, any flooring can be installed on top of the concrete.
Radiant Heaters
Tip: When heating smaller areas with a radiant
heater, it is nearly impossible to beat the simplicity
and price of an electric cable heating system.
|
|
December 03, 2008 00:12 AM  BY STACEY BARRUS
|
|
|
When replacing a
home heating system, there are a lot of questions that
people have in regards to new home heating
systems. Here is a questions that was recently
asked.
Q: My 1,200
square foot home used to be heated by a furnace from 1949
that ran at 25,000 BTU. Recently I changed the system to a
newer, 7,000 BTU system. I thought this newer heater
would be more efficient, but I find that it takes much
longer to heat the house than the older system did. Is
there something wrong with my furnace or do I need one that
has a higher BTU?
A: It’s a good idea to replace old heating
systems with newer, more efficient models. These new
models can work just as well or better than old
systems, but they do work differently. Where old
furnaces could be turned on and heat the house within a
matter of minutes, new heating systems can take
longer. If you want your home to be warm at a certain
time, set the heat to go on about 45 minutes prior to that.
Another important factor is whether your home is
“weather-tight.” Make sure all doors and
windows are properly sealed. If not, you may be losing
heat at the same rate your heating system is producing it.
Check with a heating contractor who can tell you
whether the new unit is sized correctly for your
home’s square footage.
|
|
December 26, 2008 00:12 AM  BY STACEY BARRUS
|
|
|
If you’ve
been researching home
heating systems, chances are your head is
spinning right about now. It’s no wonder!
The number of types of radiant heaters available for
residences or businesses could make anyone dizzy in no time
at all. There’s really a lot of selection for
homeowners to choose from. Today we’ll discuss
the electric cable heating system kind of radiant
heaters. Electric cable heating systems are gaining
popularity in as radiant heaters and are ideal for
heating smaller areas (10-300 square feet) like
bathrooms, kitchens, and sun rooms. These systems are
comprised of a thermostat and a heating cable. On some
systems, the cable is be shipped as a large spool of
cable. These systems are oftentimes less expensive,
and give you the ability to space the cable how you want
and customize a layout that will heat every square inch of
your floor. Other systems have the cable attached to a
plastic mesh or tape to create a mat to maintain its
proper spacing.
Every available cable system is equally
effective, so when determining which radiant heater
system to purchase, you should look at the warranty of
the product, along with the ease of installation. Some
cables must be embedded in a separate layer of
concrete or mortar, whereas other systems can simply
be installed in the thinset.
Radiant Heaters Tip: When heating smaller
areas with a radiant heater, it is next to impossible
to beat the simplicity and price of an electric cable
heating system.
|
|
December 22, 2008 00:12 AM  BY STACEY BARRUS
|
|
The number of types of radiant
heaters available for residences or businesses is
awfully mind-boggling. There’s really a
lot of selection for homeowners to choose from.
Today we’ll discuss the electric cable heating
system kind of radiant heaters.
Electric cable heating systems
are gaining popularity in as radiant
heaters and are ideal for heating smaller areas
(10-300 square feet) like bathrooms, kitchens,
and sun rooms. These systems are comprised of a
thermostat and a heating cable. On some systems, the
cable will be shipped to you as a large spool of cable.
These systems are oftentimes less expensive, and
give you the ability to space the cable how you
want and customize a layout that will heat every square
inch of your floor. Other systems have the cable
attached to a plastic mesh or tape to create a
mat to maintain its proper spacing.
Every available cable system
is equally effective, so when determining which
radiant
heater system to purchase, you should look at the
warranty of the product, along with the ease of
installation. Some cables must be embedded in a
separate layer of concrete or mortar, whereas other
systems can simply be installed in the thinset.
Radiant Heaters Tip: When heating
smaller areas with a radiant
heater, it is nearly impossible to beat the
simplicity and price of an electric cable
heating system.
|
|
December 19, 2008 00:12 AM  BY STACEY BARRUS
|
|
Hydronic under floor heating are the most
popular form of radiant heaters. This is mainly
because these radiant
heaters have been around the longest. This form of
heating was first used by the Romans, but there
have been significant developments since. In the
most recent hydronic systems, PEX radiant tubing has
been installed in a concrete mass called Gypsum
Concrete or “Gypcrete.” This
method works very well in most applications, but there
have been developments in the installation
process of hydronic under floor radiant
heaters that make it easier to install for certain
situations. This new development is known as a
low-mass or modular board underlayment system.
Rather than embedding the hot water tubing in concrete,
the PEX tubing is laid in the grooves of pre-cut
wood panels. This new method is ideal for
remodeling and most new construction projects.
If you’d like to know more about both types of
hydronic heating systems, contact the expert staff at
warmzone.com. They can help
match your individual project with the best system at the
best price. There isn’t a single system out
there that is an ideal fit for every project, but
there is an ideal system for every project. Also,
because of the relationship that warmzone.com has with the
manufacturers, they can guarantee the lowest price on
the highest quality systems available.
|
|
December 28, 2008 00:12 AM  BY STACEY BARRUS
|
|
If you are looking to warm your floors with radiant
heaters and are trying to research what kind of
radiant heaters to install you might find
yourself scratching your head at this point.
There are dozens of products available to purchase, and
there are even more companies telling you that
their product is the best.
So which product is the best?
Should you install a hydronic heating system
that pumps hot water through your floors, an electric
cable heating system, or a low-voltage screen
system? The answer lies in the type of project
you are doing. Not every system is ideal for every
project, but there is an ideal system for every project.
Hydronic Heating Systems
Hydronic floor heating is the
oldest and most popular type of radiant floor
heating. These systems are comprised of a boiler or hot
water heater, pumps, manifolds, PEX tubing,
thermostat, and either gypcrete (a concrete-like
material) or wood panels. Hydronic heating is the most
complex of all radiant heat systems. These systems
require trained professionals to design and
perform the installation. Your best economies of
scale are achieved for hydronic systems in large areas
or entire homes because of their expensive
components and operational costs.
Hydronic systems can be installed under any
type of flooring. Most hydronic systems require hot
water tubing to be installed in a 2-4″
bed of light concrete and are best installed during
the initial construction because of its weight load
demands and adjustments to floor height. Recent
low-mass products have been developed to avoid
these challenges by fitting the tubing into pre-cut
wood panels, making hydronic systems more convenient and
possible for most major remodeling projects.
If you want to heat smaller areas
like a bathroom or kitchen, a hydronic floor
heating system may not be the best value for
your project. The complexity and cost of installing the
system, along with the long-term maintenance and
up-keep required, is not worth the small amount
you will save in operational costs.
Electric Cable Heating
Electric cable heating
systems, often called line- or high-voltage
systems, are gaining popularity and are ideal for
heating smaller areas (10-300 square feet) like
bathrooms, kitchens, and sun rooms. These
systems are comprised of a thermostat and a heating
cable. On some systems, the cable will be
shipped to you as a large spool of cable. These
systems are oftentimes less expensive, and give you the
ability to space the cable how you want and
customize a layout that will heat every square
inch of your floor. Other systems have the cable
attached to a plastic mesh or tape to create a
mat to maintain its proper spacing.
Every available cable system is equally effective, so when
determining which system to purchase, you should look
at the warranty of the product, along with the ease of
installation. Some cables must be embedded in a
separate layer of concrete or mortar, whereas other systems
can simply be installed in the thinset. Most cable
systems can only be installed under tile. However, on
others, if the cable is embedded in mortar or concrete,
any flooring can be installed on top of the concrete. When
heating smaller areas, it is nearly impossible to beat
the simplicity and price of an electric cable heating
system.
|
|
December 14, 2008 00:12 AM  BY STACEY BARRUS
|
|
|
If you’re
in the market for a new home heating solution, you may be
wondering what kinds of home heating choices are there? A
majority of homeowners are probably most familiar with
forced air unit heaters and might not realize that
there are other options for heating a home – other
options that are more efficient and even more comfortable.
One such option are radiant
heaters, which, as opposed to warm air systems, delivers
the source of heat to the floor level, not the ceiling.
Radiant
heaters or radiant energy is the oldest form of heating
used to provide comfort and is the basis for all
heating systems. Radiant energy is totally pure
radiation and is absorbed by an object without physical
contact with the heat source or by heating the surrounding
air, as is the case with convective, forced air
systems. Believe it or not, under-the-floor heaters
were first used by the Romans. While under floor
heating was initially reserved for the rich, it eventually
became increasingly commonplace in public buildings
and villas. This form of radiant heating was used
particularly in the colder regions of the Roman
Empire. The Roman system was based on hypocausts, comprising
ducts that underlay the floor (itself built on raised
brick piles) and flues that were built into walls. Hot
air or steam from fires circulated up through this
system, warming the floor and walls, with heat passing into
the rooms. Radiant Heaters Tip: Health
experts agree that radiant heaters can help in
eliminating dust mites that live in our homes, and since
dust mites love a warm moist environment, towel
heaters aid in maintaining a consistent room
temperature and keep it moisture free.
|
|
November 14, 2008 00:11 AM  BY STACEY BARRUS
|
|
|
If you’ve
been researching home
heating systems, chances are your head is
spinning right about now. It’s no wonder!
The number of types of radiant heaters available for
residences or businesses could make anyone dizzy in no time
at all. There’s really a lot of selection for
homeowners to choose from. Today we’ll discuss
the electric cable heating system kind of radiant
heaters. Electric cable heating systems are gaining
popularity in as radiant heaters and are ideal for
heating smaller areas (10-300 square feet) like
bathrooms, kitchens, and sun rooms. These systems are
comprised of a thermostat and a heating cable. On some
systems, the cable is be shipped as a large spool of
cable. These systems are oftentimes less expensive,
and give you the ability to space the cable how you want
and customize a layout that will heat every square inch of
your floor. Other systems have the cable attached to a
plastic mesh or tape to create a mat to maintain its
proper spacing.
Every available cable system is equally
effective, so when determining which radiant heater
system to purchase, you should look at the warranty of
the product, along with the ease of installation. Some
cables must be embedded in a separate layer of
concrete or mortar, whereas other systems can simply
be installed in the thinset.
Radiant Heaters Tip: When heating smaller
areas with a radiant heater, it is next to impossible
to beat the simplicity and price of an electric cable
heating system.
|
|
December 26, 2008 00:12 AM  BY STACEY BARRUS
|
|
We couldn’t say it any plainer than this:
radiant
heaters are the most efficient form of heat
available in today’s market.
Significantly less operating time is required to attain
and maintain the desired warmth compared to
furnaces and other, traditional methods of
heating, which keeps operational costs to a minimum.
High efficiency boilers or
electric radiant floor systems makes radiant
heat one of your most efficient ways to heat your
home. Combined with a well- insulated home these
systems can quickly warm your home and then shut
down or wait idle for long periods of time before being
called upon by the thermostat to operate.
More than ever before, homebuilders,
househunters, and home renovators alike are
looking for energy-efficient heating options for houses.
We say they need look no further than radiant
heaters for their ideal home heating solution.
Radiant Heaters Tip: Being more
environmentally friendly doesn’t have to
involve major renovations. Many peoples’ homes
waste a lot of energy by not sealing cracks, doors and
windows. Checking to make sure a home’s
insulation is in good shape and replacing it if
it’s not is another good surefire way to stop,
prevent, and reverse energy waste.
|
|
December 24, 2008 00:12 AM  BY STACEY BARRUS
|
|
You may not know that radiant
heaters for your home or business come in a variety
of forms – all efficient and providing
reliable, cozy warmth. Today we’re going to
discuss one form of radiant heaters: hydronic floor
heating.
Quite a name, isn’t it?
Hydronic floor heating is the oldest and most
popular type of radiant floor heating. These systems are
comprised of a boiler or hot water heater,
pumps, manifolds, PEX tubing, thermostat, and
either gypcrete (a concrete-like material) or wood
panels. Hydronic heating is the most complex of
all radiant
heat systems. These systems require trained
professionals to design and perform the
installation. Your best economies of scale are achieved
for hydronic systems in large areas or entire homes
because of their expensive components and
operational costs. Hydronic systems can be
installed under any type of flooring. Most hydronic
systems require hot water tubing to be installed
in a 2-4″ bed of light concrete and are
best installed during the initial construction because
of its weight load demands and adjustments to
floor height.
For heating smaller areas such
as a bathroom or kitchen, a hydronic floor
heating system may not be the best value for your
project. The complexity and cost of installing
the system, along with the long-term maintenance
and up-keep required, might not be worth the small
amount you will save in operational costs.
Radiant Heaters Tip: Many recent
developments have made hydronic systems more
convenient and possible radiant
heater solutions for major home remodeling projects.
|
|
|